Back to top

How to locate leaks with a moisture meter

The leakage of structure in building materials from an office or a house is not new problem. In fact, you suddenly see the walls or ceiling of your home getting wet. That is not difficult to explain.These are obvious signs of a leak. Your wall has leaked in its structure.

However, finding a leak quickly is important. Because leaks not only add to the cost of water bills, the damage caused by water entering the structure can also require you to spend thousands of dollars on restoration and repair.

For many common leaks, finding and fixing the source of the problem is relatively easy. For example, if your faucet or shower is leaking, you may just require to tighten or replace a new one to repair this problem. Because the source of the leakage is in clear vision. However, not all leaks occur in simple, accessible or visible spots. Sometimes, water ingress occurs in places that you cannot see directly, such as behind walls or on ceilings, where visible signs of leakage may not appear immediately

To solve this difficult problem, manufacturers have invented a hygrometer. It is a very useful tool for detecting moisture in building materials and for identifying leaks in structures, even if the origin can be out of sight. This is why the hygrometer has quickly become an important and indispensable tool for water damage repair professionals or contractors.

How can you locate a leak with a hygrometer? Many of you have asked this question, right? In this article, I will give some tips on how to locate a leak when using a hygrometer. Let’s start reading and find out.


How to locate leaks in walls, dry plaster, bricks and concrete

Construction materials like dry plaster, bricks, and concrete usually have very little moisture in them.

However, when they leak, it is difficult to identify and place. So, how to solve this problem? Let’s get yourself a hygrometer. It helps you to discover most of those leaked locations.

Find out how to find out where it leaks now. You will require the following:

To start locating a leak, you need to set the gauge in an area of building material that you know is wet. Then, attach the insulated wire to the foundation and one of the hygrometer contact pins. When the cord is connected to one of the contact pins, apply the other pin to different parts of the material where you suspect a leak might be coming from. The battery moisture meter gives a “wet” result, the wall gets wet between the two contact points. If the battery meter shows a “dry” response, the material is not in the leak. Continue testing with other locations until you determine the leak area limit.

This procedure will help you determine the location of a leak using a hygrometer when examining building materials to ensure that the materials are in their best condition.

Find leakage on the insulating material

When the loose insulation gets wet, the moisture not only damages the building’s thermal stability, it also becomes a potential hiding place for mold. Over time, the moisture retained in the insulation will begin to affect the structures that the insulation is exposed to and cause damage.

To test the insulation, you will need to use a hygrometer with extended length probes. Because only the ends of these pins are exposed, you can easily determine the depth of insulation in an insulated bag. You don’t have to tear down the entire wall to get the insulation to start the test, you just require to drill two 3/16 diameter holes and install it an inch apart in the outer or plaster walls of your home to measure.

Once the holes have been drilled, push the pins into the holes and start reading at different depths using the reference ratio setting of your battery meter. Setting the reference rate will give you a relatively accurate assessment of any moisture present in the material measured. When you have finished reading the moisture, seal the holes drilled with suitable fillers.

Especially in cold weather, water vapor in the air will condense, which causes moisture to rise rapidly. Moreover, It causes the steam to be trapped in the insulation of the material. Therefore, you should check the humidity regularly

In conclusion

By locating a leak with a hygrometer, you can save time and money for plumber or restoration specialist to know where the leak is coming from. The less time they seek a leak to repair water damage, the lower your labor costs will be. It is extremely useful, isn’t it? Let’s consider and purchase the best moisture meter for your family right away. Finally, hope the article is helpful for you and thank you for taking the time to read.

Three Pretty Flowers for Summer (and Fall) Weddings

Q: What do these flowers have in common?

a. they bloom in time for late summer and fall weddings

b. they are grown in the USA

c. they are all the same genus

d. all of the above

These are some seriously gorgeous flowers. The answer is d: all of the above. They are all Dahlias, and they’re grown in Portland, Oregon by one guy, Mark Harvey, of Old House Dahlias. In fact, he grows more than 175 different types of them. Who says Spring brides have to get all the nice flowers? Dahlias are an absolutely gorgeous choice for wedding flowers in late summer and fall. They can get quite large and are pretty sturdy (they are tuberous), so they are a great choice for the heat of late summer and early fall weddings. Just a few stems can really add some delicious color to your wedding table.